Reloader's Nest Forum
Reloader's Nest Forum
Home | Profile | Active Topics | Members | Private Messages | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 Reloading General
 General forum
 Big Wildcat--
 New Topic  Reply to Topic
 Printer Friendly
Previous Page | Next Page
Author Previous Topic Topic Next Topic
Page: of 31

hubel458
Senior Member

USA
464 Posts

Posted - Jan 12 2011 :  04:19:09  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Penetration with slugs-Had a bunch of
wood blocks up to 12" through.

20ga load is a 54 cal 410 gr slug glued in wadcup.
Gives the same effect as Brenekke with locked on base..
Good in smoothbore at 50 yds.Goes through
6" block of wood easy/

Buckshot load in 4bore, 9 140gr 45cal balls at 1800,
all zip through 3/4" OSB and keep going.
In 4bore 760gr steel ball zips through 12" block of wood.
going over 3200 fps. Wood is dried hard poplar.

In 10ga 3.5" plastic case, a 900gr hardcast slug at 1800
fps, through same kind of block easy. This slug I put
on a screwed on base with plastic seal and wad.
I've also put plastic seals and fiber wads on 8ga
slugs to test later..

12ga 600gr hard slug at 2100 zips through 12"
wood block like it was putty.In a 3.5" RMC
case in NEF.

Anyone wanting one of my loaded 585HSMs to
collect or look at, let me know. 750gr
slug in this at 2800 in Enfield test gun.
Soon have barrel in PH and put the real
speed to it. About 33-3400.

Will soon have the heavy 20 ga barrel mono-blocked
into the 12ga barrel setup on the CBC break action.
Make a nice looking gun. Also going to put the 8ga heavy
barrel I had in Enfield for testing into falling block
built like the 4 bore one.Maybe done by summer.
Will be in one piece stock like 4bore.Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Jan 16 2011 :  02:53:00  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Finding real slow powders that works with shotgun primers,
without starter powder. We found RE-17 and surplus 7383.
To recap faster rifle powders we use -VV110,IMR 4759,4227..

On the thread we've written about real slow powders like
H-BMG we've used with a starter powder, IE 15gr of Blue dot,
and H-BMG in amounts from 150 gr to 230gr in 3.5 and 3.85
inch brass cases. And 3.5 " plastic cases. 860-1040 gr slugs.
Tested in NEF with long heavy barrel.

We finally got some RE-50,a really slow powder like H-BMG.
It works with a real magnum shotgun primer with heavy slugs,
860 gr on up, in 3.5" RMC brass, 3.5" plastic and our long
brass case. I used 239 Fed primers. Lighter slugs
only give squib loads.RE-50 Is a powder made like RE-17
with the deterrant all through the grain of the powder,
rather than all on the surface of the grains, so it will ignite
easier, to get the initial combustion started.

In brass case used 240gr with 860gr slug, 1950 fps
and 220gr with 1040gr slug, 1750.
In 3.5" plastic 860gr slug with 180gr RE-50, 1500 plus.
Now these velocities aren't earth shattering as powder is real
slow, but cases don't expand, not even plastic case base cup.
And no starter powder. Nice thing is just fill cases
leaving room for slug and seal and no worries about
to high of peak pressures with heavy slugs
or cases expanding to stick.

Now to get 239 primers get Fed 12ga long red
3.5" primed cases from BPI. I used Fed cases,and took out
primers and used in other plastic and the brass cases.
Some guys trying to free up 239 primers for us reloaders.
Federal puts them in 3.5" mag 12ga loads and 10ga cases.

Elsewhere it was reported someone may do a 16ga sabot.
Also a guy got huge antlered buck with hotrod 20ga. Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Jan 20 2011 :  12:42:45  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
I have a way to compare primers without powder and slugs,
for a lot of my experimenting. I use a short 24"barrel 10ga.
The barrel being shorter I can see the sparks and flame.
I fire off the primers in case with no powder/slugs.

I have just tested to see if magnum FED Fusion and Triple 7
inline muzzleloading primers were as strong as FED 239.
Just the two brands to test in the 10ga to compare flame,
sparks and bang, and they were not as good as the 209
Remington STS ones I like. They only put a few sparks out
of the barrel.The REM 209 STS and Fed 209 M had 3" fire out the
barrel and the Fed 239 had about 5-6" out the barrel. And 8ga
Rem and Win kiln case hotrod primers 8" plus....

Previous post I mention trying to start H-BMG slow powder with
8ga kiln primers without success. Which is why we figured out
using a starter powder like 15gr Blue Dot. Then it works great
with any shotgun primer. Guys here when they see misfires with
shotgun primers and H-BMG only, and the see starter powder loads
go off in our big 12ga case like a tank cannon, they are
flabbergasted at the difference.ED

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Feb 09 2011 :  05:18:24  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
I mentioned in the threads earlier a 16GA FH case
I made from bmg brass. Then I put it in a 16ga
Stevens 94 break action by lengthening chamber
for the 3.5" case. I kept speed and pressures down
as the regular barrel on the gun had a thin muzzle.
Now I found a thick heavy 16ga 32" alloy tube and
I had extra Enfield test action, with the port
opened for longer cases. I turned it 1.1" at the
muzzle. Nice and heavy. It does a 630gr 16ga
'Greg S' slug 2400 and 385 gr Lightfield 16ga slug
to 3000, without the bottom 2/3 of the case
having to be resized. With RE-17. I have these cases
setup for shotgun primers.The Lightfield has it own
seal on the locked on base and for the 630 gr use
a BPGS type of seal and Flex type cushion over powder.. Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Feb 26 2011 :  03:32:19  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Here is picture the CBC 20ga FH setup
by mono-blocking a heavy 20 ga barrel
into a CBC 12ga breech section.The 20 heavy
barrel is threaded into the mono-block made
by cutting off 12ga barrel. These CBC actions
are taller and wider than other break actions
and the locking lug block works better and
nicer than other break actions.Also shown
is 20ga 3.5" plastic and brass cases.
Second picture is PH action with port lengthened
for 585HSM, shown in action. I also have second
change barrel for 700HE long case for this action.
Imagine over 20,000 ft lbs in a PH, for 700HE.
Also shown behind is a PH with 700H 3.25"..Ed


Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Mar 05 2011 :  05:31:56  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Here are some 20ga slugs/sabots we rigged up.
I traded for whole box(hundreds) of 20ga Hammerhead
slugs, in the picture. They had pulled slugs
out of the locked on plastic base, so I glue them
back in so base stays for fair smoothbore accuracy.
And I also glued in various 458 bullets, as shown,
which fit tight in cup, up to 500gr. They discard
on impact. Fair accuracy at 50-70 yds. Less expensive
shooting as I have pile of hard lead 458 slugs.

Idea on 8ga FH. Looked at a TCR87 break action 10ga
and the breach mono-block can take a little bigger
barrel.If I find one I can afford(pricey) I'll do 8ga.
These are very strong actions, a little smaller version
of the action setup Colin put the 2bore in.
Just put in straight 8ga bull barrel like NEF Ultra.ED



Ed Hubel
Go to Top of Page

hwy40
Advanced Member



USA
552 Posts

Posted - Mar 05 2011 :  10:35:14  Show Profile Send hwy40 a Private Message  Reply with Quote
Ed, would you elaborate on the process of mono blocking? I'm interested in modifying a break open single shot.

If it ain't broke, fix it 'till it is.
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Mar 11 2011 :  04:10:37  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
A few break action guns are built by mono-blocking.
This allows the pivot block and breech section to
be one piece as opposed to welding/brazing pivot block
to the barrel. The barrel is then pressed/threaded into
the monob-block. And we using break actions can do the
same by cutting off barrel and putting in new barrel.
We still have the breech and pivot fitting the action and
much easier with a lathe as opposed to taking new barrel
and making pivot block and welding it on like big
factorys can.

Here is picture of the 4bore in a more finished look.
Second picture is closeup of cases and 1520 gr
hollowbase hard slugs. The 4bore is smooth bore so
hollowbase slugs are used. I set up gun with
smoothbore as that saved large amount of time and
money on the barrel. Ed




Ed Hubel
Go to Top of Page

hwy40
Advanced Member



USA
552 Posts

Posted - Mar 11 2011 :  08:11:44  Show Profile Send hwy40 a Private Message  Reply with Quote
Thanks for the info Ed, This is a hell of a project you have going.

If it ain't broke, fix it 'till it is.
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Mar 21 2011 :  12:28:37  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
I found a few long brass 8ga cases to go with
the 3.3" plastic ones. They are an inch longer
and made by RMC. The 8ga barrel I'm putting
on a falling block will have the chamber long
so I can use both lengths of cases.
The plastic ones are from 8ga kiln cases with base
swaged a little and has shotgun primers, The
long brass has shotgun primers.
I use Fed 239 shotgun primers.Ed


Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Mar 29 2011 :  04:08:02  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
The long brass 8ga cases have same thick
sides as plastic cases. And there are long
plastic/paper cases out there, but they
are scarce. Thick sides mean a good chamber
fit, so as to minimize case expansion and make sizing
easier. Here is picture 8ga and 10ga fullbore slugs with
locked on basewads that I setup. Wads held on by
screws and slugs hollowbase as well, so to work in
smooth barrels with some accuracy. 8ga is 1100gr.
10ga is 900 gr.Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Apr 04 2011 :  06:19:35  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
New super strong 12ga bolt gun just out, Savage 212, taking
over for the 210. You know I did my first 12ga FH in a 210 and
have posted that sometime I'd like to get a thicker walled
reciever built to have more strength and safety.
Well Savage helped us out.

Its reciever is 1.5" diameter, where the 210 was 1.36" dia.
I has a large .900" diameter bolt, where the 210 had regular
110 bolt inside bolt carrier. It has a fitted bolt head like 210
and other Savage 110-116 rifles. Only its bolt head has two lugs
where the 210 had 3 lugs. Its two lugs about 90% strength as
the 210s 3 lugs.Its about 12% stronger lugs than Enfield and
Rugers. Also it appears the bolt raceways are not through the
barrel thread area so about 50% stronger barrel connection.

Price not too bad 500-550. I'll try to find one later to do some
hairy cartridges in. It has a 3" 12ga chamber from factory and
detachable magazine. Probably can have mag and port lengthened
and feed ok, with 3.5" 12ga and the 700H 3.25". More info
as I find out stuff.Picture from auction-e.Thanks to
Bob in OR for info.Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Apr 13 2011 :  03:47:49  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Some more info on the Savage 212. I looked at one,
got more measurements. The port is 3.812" long.
Can be made longer. Bolt travel is 4.625" and can be .50"
longer. And with full diameter bolt can have extra
lugs in back. The Mag box has room for extra length in
front of it and behind it. It could work for 12ga FH
and 700HE long case.

A fellow on Gunsmithing forum found a way to make
jacketed slugs using copper tubing caps, the solder ones,
by putting them in a die and using a shaped punch to form
a round nose copper jacket, that can be filled with lead.
He made .700 cal ones, different dies/punchs could
be made .729, 12ga size. I got a few here and going to see
what is possible. I got bigger caps also to see about 4ga
and 8ga ones. Here is picture of the CBC break action with
the 20ga heavy barrel mono-blocked in, with action open.Ed


Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - Apr 28 2011 :  00:22:35  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Would have posted back quicker but computer
hookup down for afew days..
Here is picture of 16GA FH I mentioned earlier doing in
an Enfield bolt gun. Got 630gr slug 2400, compared to
the first 16GA FH in thin barrel break action at 1600.
I use 630 gr full bore slugs and the 385gr SPW
saboted with locked on bases.

Opened port and changed bolt stop on Enfiels action. Reamed
front so case fit through action into barrel and added extra
rear lugs. Same process that is used to do Enfield
bolt action in my 700H 3.25.
I got some of the work done on 8ga in my falling
block design, like the 4ga I've done pictured earlier.
Will get pictures posted later..Ed

Ed Hubel
Go to Top of Page

hubel458
Senior Member

USA
464 Posts

Posted - May 11 2011 :  03:51:10  Show Profile  Visit hubel458's Homepage Send hubel458 a Private Message  Reply with Quote
Experimenting for fellows trying to get speed with heavier sabot slugs than
the lightweight saboted 4-500 gr kind of slugs, in 2 5/8" length brass
cases for where length is limited..

Using 770 gr sabot slugs with locked on base, by US-S.
These are long sabot slugs due being brass and locked on base.
Real hard to do with these due to lack of powder space for the RE17
and IMR 4759-4227 that I like to use. With 770 gr and 60gr 4759 got 1450 fps.
With 75gr Re17 about 1350 fps. Both of these all case will hold under sabot.

For contrast using full bore 730 gr Dixie with just seals under it, much more
powder room, with 95gr 4759 getting 1800 plus and 130 gr RE17 1700 fps.
I went to faster powder, my slowest shotgun powder, Alliant steel, to try to get
speed like full bore slugs get.

These listed are max loads before brass cases expanded to much and started
sticking, due to sharp expansion step, where the base goes to the side with a
real small inside radius on this particular RMC brass case.
47gr Steel,and 770 gr slug 1400 fps.

So I tried the 570 gr US-S with 53gr Steel,and got 1700 fps. Same slug with
65gr 4759 got 1650. You can put in more Steel but cases stick more.They won't
blow up, just stick. And cases expanded that way are hard to resize.

The first 3" brass I got years ago, same problem with
a sharp step expanding above the base. So when I had 3.5" brass made
I had them do a long inside radius from base to the sides. These with extra
room for powder and cushion are much less problem. I think where you have
to use shorter cases, you can use plastic, as a 3" plastic is 2 5/8"
when crimped and will do the same and only be 20 cents or so new.Ed

Ed Hubel
Go to Top of Page
Page: of 31 Previous Topic Topic Next Topic  
Previous Page | Next Page
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
Reloader's Nest Forum © 2016 ReloadersNest Go To Top Of Page
This page was generated in 0.28 seconds. Powered By: Snitz Forums 2000 Version 3.4.06