Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!
|T O P I C R E V I E W
||Posted - Jan 23 2006 : 13:47:39
I am new here--and want to share a result of, mine and
couple others over on AR, mad wildcatting.
It is called the 12GA From Hell--A long brass 12ga case
we made by putting a 12ga size rim on BMG brass and
straightening case out. Rob and John on AR put theirs
in big Borchardt falling block actions and I put mine in
a Savage 210 bolt action shotgun with heavy barrel and stock.
I got a 730 gr Dixie terminator lead slugout at 2700 fps,
and 3/4 oz Barnes saboted slug out at 3900 fps.Here is
picture of the case next to regular plastic shell, which can
be fired in the chambers of our guns.Ed
|15 L A T E S T R E P L I E S (Newest First)
|hot chilly powder
||Posted - Sep 10 2014 : 17:35:09
Seems like a lot of work but hey, whatever trips your trigger (or breaks your shoulder). Bet you are hoping for a return of the mammoths!
||Posted - Sep 10 2014 : 04:32:45
First AUS buffalo killed by 585HE. By Tankhunter with his Ruger #1.
If you use closeup on picture, you see loaded round on the buffs hide
next to the 585HE Ruger #1.... A nice heavy barreled gun..Ed
I put the 585 in a Savage 112, lots of room lengthwise, figuring out an
extractor is a problem, but then got a look at the savage 212, the 12 ga
one with big diameter bolt and locking lugs. Its locking lugs are bigger
than the lugs in a big PH bolt action. So one day will do one
on a Savage 212, and adjusting extractor to fit no problem...Ed
||Posted - Aug 17 2014 : 13:45:09
Finally got back to forums.Been busy with 24ga FH and 585HE
and getting 585HE cases made, as many as possible...
We are now working a bit with 24ga FH and here is picture
of it with our 585HE case. Both use same bullets/slugs, same
bore barrels. Main use difference, 24ga FH easy setup in break
actions and 585HE in bolt actions and falling blocks.
Picture of non-discarding 585/24ga sabot cup I found that holds
458 bullets and slugs tight. It had hammerhead type slug in it that
was pulled out, wouldn't stay in tight after pulled. Sabot was a loose fit
in 20ga, though made for 20ga, but small, so I shrunk the bottom rib,
fits perfect, super tight, in 24ga and 585HE. A press in fit gives
good resistance for good ignition.
Here is another 24ga/585 sabot that holds .452" 45cal pistol
bullets. Made by Hornady for 58cal Muzzle loaders..
With 250 gr bullet in 585HE hot load will go about mach 4.
Here is easy way to weight plastic stocks with hollow butts, use rubber
coated computer mouse balls, weight comes out perfect without being
too heavy if using that much lead.And coating keeps them quiet, and
we hold them in with piece dense foam under butt pad....Ed
||Posted - Apr 23 2014 : 22:45:16
Here is picture of 24ga cases, loads; and some slugs and seals.
Brass cases are 3", plastic cases are 2.5". Brass 3" can be loaded
to match 577NE power.
Here is of 24ga in an 87 Win, just test gun of mine. Uses same barrels
as our 585HE, This one has slow twist for Minie bullets.Our guys
have got supply of regular and slow twist barrels.
Here is picture of the first 585HE done and shooting in Australia.
It is owned by the poster, 'tankhunter' on the AR forums.
Built by his smith who has a reamer.
Guys there can get cases from Bertram, and there will soon be three
reamers there. There is a company there now making 585 barrels,
Allan and Grant Swan. in Redbank, Queensland.....Ed
||Posted - Mar 13 2014 : 23:12:54
Here is good simple system with big hollowbase slugs to stop
the skirts from deforming, or wads getting pushed into
the hollow base. I found that dense dow foam works
good, I was using glue gun, but the dense foam is easier, cut
plugs out of foam sheet and force into the base. Make it a
tight fit, use spot of glue inside, glue that is for foam....
Trim off the foam flush..In picture is 10 ga 900gr slug
with foam pressed into the base..
How we get good 24ga plastic seals with protusion on
top that fits up inside 58cal Minie base, same bore as 24ga
and our 585HE. I get the 24ga seal by cutting apart the BPI
24ga Brush wad, getting two seals out of each.Works great
in plastic case giving a shorter column than other seals and
wads, so we can get in enough of our 4759 for good speed.
The 24ga idea is getting nicer all the time with
the variety of cheap 58cal slugs, and good 3" brass cases,
drawn cases, we didn't have to wait to get made.
And all kind of guns we can use, bolt 395 Mossbergs, single
shots of all kinds, Autos,, pumps. bolt action Savage,
even 1887 Win and Greener MKIII, bolt action JC Higgins. .
Here is picture Khan auto we setting up 24ga FH, it is 3.5"
model, has a 12ga barrel to change with. Being 3.5" it
feeds/ejects through lengthened port 3" brass 24ga cases we
made from 577NE brass. We rework back of the bolt for
slightly longer stroke.Ed
||Posted - Feb 23 2014 : 17:15:07
Some guys in 12ga like to use the Magtech brass cases
but the cases being brass the sides are thinner than
plastic, and that makes loose fit in 12ga chambers.
And cases expand a lot with heavier loaded slug
loads, are harder to resize, wear out quicker.
But I found that .750 hollowbase 10ga slug fits
those cases and still chambers in regular 12ga.
chamber, it isnt a sloppy fit.
So If you have a 12ga smooth barrel with full length
backbore job, of .850" bore or bigger you could use
the Magtech brass and .850" size 10ga hollowbase slugs.
Now these .850" slugs won't go in a 12ga plastic case
and chamber in regular 12ga chamber.And you do not
fire them through 12ga regular size barrel.
Brett in MN used the a BPI AQ slugs in his full length
backbored 12ga and got fair accuracy as he said the wads
under slugs expanded a lot for a decent fit.
The 10ga slug shown in the 2.5 inch Magtech is 800 gr,
and .850" diameter. These cases will take magnum
pressure so you can get good speed, for what this short
case can hold.
It is too bad they don't make 3" and 3.5" versions.
These 2.5" cases are easier to find and much less than
others, so if needing brass ones you can rig up guns
to work with them. To build a new barreled gun in actual
12ga size, IE .729" bore, you'd make chamber to
minimum specs so cases don't over expand.
In the picture are 2 10ga slugs on right, like in the case,
and 2 12ga jacketed slugs and one 12ga lead slug left.ED
Here is the ytube URL again for our guy
shooting 585HE in his NEF----By mid summer we plan on a
pickup truck load of more 585HE cases coming in.
||Posted - Jan 28 2014 : 02:49:36
Here is picture of 24ga FH in the Mossberg bolt gun. On a
Mossy 390 frame, .585" heavy barrel, same as 24ga size.
Chamber is set up 3" with shotgun style forcing cone,
so it can use 2.5" plastic cases and 2.5" Magtech brass
cases with slugs or shot and for 3" cases we use 577NE
3" brass. Really make a hairy 24ga using the 440gr to
540 gr Minie bullets at 21-2400. If you take 540 Minie bullet
mould and leave out base pin you'd have a 650gr that
would do. All these bullets and slugs as well as jacketed and
turned 577/585 bullets work in 24ga as well as my 585HE.
And the smaller Minies work in our 12ga sabots. I keep
saying 58cal is where it is at, and there are more bullet and
slug choices in the .585 size, easy to find, than any other
caliber over 458. And Minies are like 40 cents each and
cheaper if you cast your own.
Here is picture .585" barrels from McGowen, with other barrels.
Most of the McGowens profiled and some straight blanks.
Others we have are the slow twist and smooth blanks...
In back some of the cases and die sets.
Here is picture of an Enfield and a BBK in Hogue recoil
reducing stocks. These stocks are the rubber coated ones with
the easy to grip, nice pistol grip.Has McGowen 26 inch barrels,
1 to 20 twist, barrels are heavy profile and taper
to .980 inch at the muzzle. Guys are doing more Enfields
and other actions through the winter. Ed
||Posted - Jan 01 2014 : 18:16:52
Thanks for the encouragement..
Another use for 58cal Minie Bullets would be to setup a 24ga FH.
Minie bullets cheap to cast and buy. We use the .575-.577" in our
12ga sabot, and the .585-.587 in my 585HE. And you could use
577 NE bullets also.
For those in shotgun only areas there is a way. You can get 2.5"
Magtech brass cases, but also you can set up a 3" chamber and use
577NE 3" brass. Grafs shows some under 4 bucks each. Cheaper
than getting them made. And if you set up chamber with shotgun style
forcing cone you could shoot shorter Magtech as well as plastic cases.
Reason to use 577 cases, they are stronger solid head, last forever,
and can be run higher pressures and still last forever.
You can get barrels, 58cal at Green Mtn I think. .We got some also.
AND the first batch 585 barrels from McGowen has got here, more
will be built.They are the regular 1 to 20 twist barrels, and we have 14
that are profiled and polished, and 3 others that are straight blanks,
1 to 20 twist. And 6 slow twist barrel blanks for guys doing mainly
Minie bullet guns, and bunch smoothbore blanks...Pictures soon.
Here are couple pictures of a 585HE gun a guy is doing with nice
walnut stock. Gun has extra bedding lug and accra-glassed.
It is an Enfield and has single stack magazine.
||Posted - Dec 10 2013 : 10:59:40
Looking at some of the posts on this forum, I quickly realize that I know squat.... No.. I know less than squat....
Stuff like this is ingenuity that just astounds me.....
||Posted - Dec 09 2013 : 02:30:12
Here is picture of the group improvement a guy had shooting our
sabots in a real tight barrel. Actually an undersize barrel compared
to Savage and Nef barrels. Had a wide open group with shotgun
powder but made it much smaller using much more
of the slower 4759.
There is a guy now in Canada with our sabots for guys there and
other countries, and as well, he can ship back to here. He plans
on supplying the .58cal slugs also for the sabots if guys can't get
them or don't cast their own.......
Contact is- jeff.a.white at gmail.com
If things work out for him he plans on getting a bunch
our 585 cases imported for guys to get there also.
I got some factory 8ga kiln loads, 3 oz lead at 1800 in the long
barrel falling block. Got box of 25 to see how they compared to the
loads we setup.They go faster in long barrel than in short kiln guns.
Our favorite is 900gr in the 8ga wadcup at 2300, in plastic case.
Here is picture of section 585HE case showing 4 pyrodex 54cal,
60gr equivalent pellets, with a 440 gr Minie bullet.
Actual powder wt is about 185gr....Goes about 2600.
Nice cloud of smoke and really bellers out of the slow twist barrel
barrel we set up for minies.....Top pellet I tapered a little and fit it
inside the hollowbase of the bullet.That's how to get 4 pellets in....Ed
||Posted - Oct 16 2013 : 11:19:13
In above post we compare the top thickness of sabots
.Here is comparison of the thickness of the sides of two types of
brass 12ga cases, the RMC turned case and the thinner
Magtech drawn case. Easy to see you can't size with same dies
and sometimes you have to use different wads..
In posts earler in the thread you saw variety of wad columns with
12ga sabots and here is picture of my favorite wads to go between
seal and sabot. The white felt ones from BPI. They compress down
evenly on firing, easy to load, decent price,
You've seen the work on our 585HE posted. Folks ask what case
I made first ones from and how. Here is a sketch showing the steps
I used to make the first 585HE from long basic straight Nyati brass.
The start of the belt step I put on the case where it is thick I do it
in my case spinner lathe I made. Then case is lubed and run into
couple swaging/sizing dies and comes out formed into our belted,
straight sided, 585HE case...... It is really faster getting a big
run of cases made in a factory.
Shot a 12ga sabot load w/440 gr Minie bullet in smoothbore Rossi
in 3" case, Going about 1700... .. 4" group 3 shots at 30 yds.
Gun works fine, shoots nice. Got extra weight in the butt.
The Minie I used is a semi-round nose. If I had the ones of same length
with blunt nose, slightly heavier the group size would be smaller as
they'd be more nose heavy, be like Foster slugs..Ed
||Posted - Sep 15 2013 : 15:37:45
Here is picture of our 12ga sabots with the marks that the barrel lands made, marked with
black marker. The one with narrow mark is Savage barrel and one with wide mark is
an Abolt barrel. And the ones fired in Savage and NEFs with the narrow lands the marks
impressed into the plastic getting good bite and not twisting the petals. The one from abolt
he used slower powder for easier start and it open petals ok, without twisting petals like
the faster powder did for him.
Next is picture showing top edge of sabots. Our sabot on left you roll crimp down over
the inside of it a little . We have lots of them yet.
The other factory sabot they crimp real short and sharp
180 degree crimp down on top of it.
We see a use for modified 585 application in Indiana deer hunting. Mainly shotgun only, but
they also allow rifles with over 35cal pistol calibers; and any over 35cal rifle with a case
1.8" or shorter, usually short wildcats. So we have the the 585 HI... The I is for Indiana.
Here is picture of it next to the kinda little 500 S&W. 585 HI holds over 80 gr powder.
Next picture is a Magtech chambered for it. Gets 440gr Minie over 2,100 fps.
The .585"- .587" Minies of 440gr, 540gr, etc work in it, and they're good deer slugs
We got other guns with it going into; bolt guns, like in the last picture,
single shots and checking couple lever actions.
Might work great in MNs many guys like....Ed
||Posted - Aug 21 2013 : 20:53:34
One of our sabot testers with tight barrel, 12ga Abolt, with wide lands in
the barrel, who couldn't do any good at all with our sabot and Alliant Steel
and one type of slug, had to go to IMR 4759 & different slug.
It would twist up the sabot petals. Terrible accuracy.
My guns have NEF/Sav size barrels and worked fine with Steel as well as 4759.
Petals open perfect here. The Abolt barrel about .005" smaller than NEF/Sav and
the lands over twice as wide as the NEF. And has real narrow grooves.
Guys with Nefs say sabots open fine like ours here.
He went to different Minie slug and our slow powder loads using
IMR 4759 powder up to 78-79 gr and finally got down to 2.5" group, I told him
go to max which is about 80-82 in 3" case.That barrel is like a lot of
EU made barrels and many are replacement or add on barrels in many slug guns,
and that is reason why it is so hard to get accuracy across the board in
sabot shooting in all guns--Takes a lot of work.. Another tester with NEF 12ga using
Alliant Steel with sabots got good groups like we did here. I tell guys if
problems occur go to 4759.
What was happening to sabot petals in the barrel, with the extra tight fit and
wide lands were petals twisting.. The wide lands were not cutting into the base of
sabot like in NEF/Sav210 barrels. The twist effect of rifling was on the surface
of petals, twisting them. It was not getting good hold on the sabot body. The
4759 starting slower allowed the sabot to get its spin started up to speed
with the wide land rifling and narrow grooves..It is just the opposite of
way NEF/Sav 12ga barrels are done. with narrow lands which impress into
the sabot base the way it is supposed to work..I showed pics above of the
good rifling marks impressed into our sabots.
I think after this experimenting run I feel that a lot of accuracy problems
across the spectrum of barrels are due to barrel differences, and not just
the differences in factory slugs and/or reloading components.
Here is pic of bag of our 585 cases with plain head if some need them for
wildcatting.We have quite a few. Fifteen have 585HE cases now. 585 gun
building is accelerating. We can get folks going with 100 cases, dies, and soon
a barrel; and shipping, for 750...Ed
||Posted - Jul 19 2013 : 00:43:35
Here is picture of current 58cal slug options that
you can get molds for from Lyman,
Just make sure they are .574" to .577" diameter,
the best size for the 12ga sabots.
A barrel of 585HE cases..Ed
Made by Bertram and I tested them to max loads and cases hardly expanded,
650gr over 3000 fps. The same draws used by him to make high pressure
Cheytac cases, and to finish mine just uses belted header and cases left
straight and trimmed longer.He makes tens of thousands Cheytac steady all
the time now and can make ours steady also when needed.....Ed
||Posted - Jul 06 2013 : 04:12:15
We have moved few thousand sabots.More here.
Here is picture of an 8ga wad with tube slug in it, we made.
A pallet load of our 585HE cases has arrived in the US
and will be here in little while. And should be another pallet
of them this fall. Here is picture of our 585
with the solid turned CEB bullets in them.
Here is some helpful, simple math to help figure out the kinetic energy
of your loads, just by having bullet weight and speed.
Just put these multipliers which are used for each speed, on a list
and multiply by the bullet weight in grains. Fast and easy.Ed
|Reloader's Nest Forum
||© 2013 ReloadersNest
|This page was generated in 0.08 seconds.